Mold Remediation
Professional mold removal and remediation services following industry best practices with proper containment, HEPA filtration, antimicrobial treatment, and complete source moisture elimination for Calgary properties.
Why Professional Remediation is Essential
Improper mold removal can actually make the problem worse by releasing massive amounts of spores into the air and spreading contamination throughout your property. DIY attempts often fail to address the underlying moisture source, allowing mold to return quickly. Professional mold remediation follows strict protocols to safely remove mold, prevent cross-contamination, and eliminate the conditions that allowed mold growth.
Our certified remediation specialists use industry-standard containment procedures, HEPA filtration systems, proper personal protective equipment, and EPA-approved antimicrobial treatments. We don't just clean visible mold—we address hidden growth, repair moisture problems, and verify complete remediation with post-treatment testing.
Never Attempt DIY Mold Removal for Large Areas
Any mold growth larger than 10 square feet should be handled by certified professionals. Disturbing large mold colonies without proper containment and protection can expose you to dangerous spore levels and spread contamination.
Our Complete Remediation Process
Initial Assessment & Testing
Before beginning remediation, we conduct a thorough inspection to document the extent of mold growth, identify moisture sources, and develop a detailed remediation plan. This includes air and surface sampling to establish baseline contamination levels.
- Complete property assessment and moisture mapping
- Pre-remediation air quality testing
- Detailed remediation protocol development
Containment Setup
We establish physical barriers using heavy plastic sheeting to isolate the contaminated area from the rest of your property. This prevents mold spores from spreading during the removal process. Containment areas are sealed with tape and negative air pressure is established.
- Physical barriers with 6-mil polyethylene sheeting
- Sealed entryways with zipper doors or antechambers
- Protection of HVAC systems to prevent spread
Negative Air Pressure & HEPA Filtration
Industrial HEPA air scrubbers are installed inside the containment area to create negative air pressure, ensuring that any airborne spores are filtered and cannot escape into clean areas. These machines continuously filter the air throughout the remediation process.
- HEPA-filtered negative air machines capture 99.97% of particles
- Continuous air pressure monitoring
- Air exhausted safely outside the building
Source Moisture Elimination
Mold cannot be permanently eliminated without fixing the moisture problem that caused it. We identify and repair all moisture sources including leaks, condensation, humidity problems, and water intrusion points before or during the remediation process.
- Repair of plumbing leaks and roof penetrations
- Improvement of ventilation and airflow
- Installation of dehumidification if needed
Removal of Contaminated Materials
Porous materials that cannot be effectively cleaned are removed and properly disposed of. This includes drywall, insulation, carpeting, and ceiling tiles with significant mold growth. Materials are double-bagged and sealed before removal through the containment area.
- Careful removal to minimize spore release
- Materials sealed in disposal bags within containment
- Proper disposal following regulations
Cleaning & Antimicrobial Treatment
All remaining surfaces in the affected area are thoroughly cleaned using HEPA vacuums and antimicrobial solutions. Non-porous materials like wood framing, concrete, and metal are cleaned and treated to eliminate mold spores and prevent regrowth.
- HEPA vacuuming of all surfaces
- EPA-registered antimicrobial treatments
- Cleaning of contents and belongings when possible
Drying & Dehumidification
The remediated area is thoroughly dried using commercial air movers and dehumidifiers. We monitor moisture levels daily to ensure all materials reach safe moisture content levels before reconstruction begins.
- Professional drying equipment deployed
- Daily moisture monitoring with meters
- Verification of safe moisture levels before closure
Post-Remediation Verification
After cleaning and drying are complete, we conduct post-remediation air quality testing to verify that mold spore levels have returned to normal. Visual inspection confirms no visible mold remains. You receive clearance documentation for your records.
- Post-remediation air quality testing
- Laboratory analysis confirming successful remediation
- Written clearance certificate provided
What's Included in Remediation
Complete Containment
Full physical barriers and containment systems to isolate work areas and prevent cross-contamination to unaffected areas of your property during the remediation process.
HEPA Air Filtration
Industrial HEPA filtration systems creating negative air pressure and continuously filtering airborne mold spores throughout the entire remediation process.
Safe Material Removal
Professional removal and proper disposal of contaminated materials including drywall, insulation, carpeting, and other porous materials following safety protocols.
Antimicrobial Treatment
EPA-registered antimicrobial and antifungal treatments applied to all affected surfaces to eliminate remaining spores and inhibit future mold growth.
Verification Testing
Post-remediation air quality testing and laboratory analysis to verify successful mold removal with clearance certificate for insurance and documentation.
Moisture Control
Identification and repair of moisture sources, installation of vapor barriers, improvement of ventilation, and recommendations to prevent future mold growth.
Common Remediation Scenarios
After Water Damage or Flooding
Water damage from floods, burst pipes, or sewage backups requires immediate action. Mold can begin growing within 24-48 hours of water exposure.
- Emergency water extraction and drying
- Mold prevention treatment if caught early
- Full remediation if mold has developed
Attic Mold from Roof Leaks
Roof leaks, ice dams, and poor ventilation commonly cause attic mold. Contaminated insulation must be removed and ventilation improved.
- Roof leak identification and repair
- Contaminated insulation removal
- Ventilation system improvements
Basement Mold Problems
Foundation moisture, flooding, and high humidity cause basement mold on walls, floors, and stored items. Waterproofing is often required.
- Foundation moisture control
- Removal of moldy drywall and contents
- Dehumidification system installation
Behind-Wall Mold Growth
Hidden mold behind walls from plumbing leaks or exterior water intrusion requires careful investigation and targeted remediation.
- Thermal imaging to locate moisture
- Controlled wall cavity access and cleaning
- Plumbing repairs before reconstruction
Bathroom Mold Issues
Poor ventilation, shower leaks, and high humidity cause mold on tiles, grout, caulking, and behind walls in bathrooms.
- Exhaust fan upgrade or installation
- Shower pan and tile repair
- Mold-resistant materials for reconstruction
HVAC System Contamination
Mold in HVAC systems spreads spores throughout the entire building every time heating or cooling runs. Professional cleaning is essential.
- Complete ductwork cleaning and sanitization
- Coil cleaning and drain pan treatment
- UV light installation for prevention
Pricing & Timeline
Cost Factors
- Square footage of contaminated areas
- Extent of mold growth and contamination levels
- Type of materials requiring removal and disposal
- Accessibility and difficulty of work areas
- Extent of moisture source repairs needed
- Post-remediation testing and clearance requirements
Insurance May Cover Remediation
Many homeowner policies cover mold remediation resulting from covered water damage events
Project Timeline
Small Projects (1-2 rooms)
2-4 days for remediation plus 2-3 days for drying and verification
Medium Projects (3-5 rooms)
5-7 days for remediation plus 3-5 days for drying and testing
Large Projects (whole home/building)
1-3 weeks depending on extent of contamination and reconstruction needs
Emergency Response
Can begin containment and mitigation within hours of your call
24/7 Emergency Service
Immediate response for water damage and urgent mold situations
Frequently Asked Questions
Do I need to leave my home during remediation?
In most cases, you can remain in your home if the remediation area is properly contained. However, for large projects, extensive contamination, or if family members have health concerns, we may recommend temporary relocation during active remediation.
Will my belongings need to be thrown away?
Non-porous items like glass, metal, and hard plastics can usually be cleaned and saved. Porous materials like upholstered furniture, mattresses, carpets, and papers may need to be discarded if heavily contaminated. We'll assess each item and clean what can be salvaged.
Is the mold guaranteed not to come back?
If the moisture source is properly fixed and conditions remain dry, mold will not return. Our remediation includes fixing moisture problems and providing prevention recommendations. We offer warranties on our work when moisture control measures are maintained.
Do you handle reconstruction after remediation?
Yes, we offer complete reconstruction services to restore your property after remediation. This includes drywall installation, painting, flooring, and other repairs using mold-resistant materials when appropriate.
Will my insurance cover mold remediation?
Many homeowner insurance policies cover mold remediation if it resulted from a covered peril like a burst pipe or storm damage. We work directly with insurance companies, provide detailed documentation, and can assist with your claim process.
How do I know the remediation was successful?
We conduct post-remediation air quality testing and visual inspection to verify successful mold removal. You receive laboratory results and a clearance certificate confirming that mold levels have returned to normal and the space is safe to reoccupy.
Need Professional Mold Remediation?
Don't let mold damage your health and property. Contact us for professional remediation with 24/7 emergency response.